Interfaccia seriale DAP-1325 HW A1
Velocit??: 57600, Data bits:8, Stop bits:1, Parity:none, Flow control:none
Log di avvio DAP-1325
[04060C0E][04060C0B]
DDR Calibration DQS reg = 0000888A
U-Boot 1.1.3 (Dec 2 2016 - 21:11:16)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb0000
flash manufacture id: ef, device id 40 17
find flash: W25Q64BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Dec 2 2016 Time:21:11:16
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
k: Load system code then write to Flash via Web.
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5625199 Bytes = 5.4 MB
Load Address: 80000000
Entry Point: 8000c150
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@mtn) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #17 Tue May 15 11:43:28 CST 2018
The CPU feqenuce set to 575 MHz
MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0005930f
Readback ErrCtl register=0005930f
Memory: 56404k/65536k available (3287k kernel code, 9084k reserved, 760k data, 4240k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 110
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
i2cdrv_major = 218
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 17
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully.
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
=== pAd = c014d000, size = 1408928 ===
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(492): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()
u32 classifier
Performance counters on
nf_conntrack version 0.5.0 (881 buckets, 3524 max)
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Warning: unable to open an initial console.
status_socket_nl_create
kernel_init:Netlink socket create ok!
Freeing unused kernel memory: 4240k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
__ ___ _____ _____ _ _______ ______ _____ _ ___
| \ / || ___|| __ \ | || __ ||__ __|| ___|| | / /
| ^ || |__ | | \ \| || | | | | | | |__ | |/ /
| | | || ___|| | | || || |__| | | | | ___|| \
| | | || |___ | |__/ /| || __ | | | | |___ | |\ \
|__| |___||_____||_____/ |_||_| |_| |_| |_____||_| \__\
= Everyday Genius =
led=11, on=1, off=4000, blinks,=1, reset=1, time=4000
led=37, on=4000, off=1, blinks,=1, reset=1, time=4000
TX_BCN DESC a2b7c000 size = 320
RX[0] DESC a2b7f000 size = 1024
RX[1] DESC a2b80000 size = 1024
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
load fw image from fw_header_image
AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
FW Version:20151201
FW Build Date:20151201183641
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000012
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
Country Region from e2p = 1ff
tssi_1_target_pwr_g_band = 28
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(11): Not support for HIF_MT yet!
NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
AntCfgInit(2940): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
CmdSlotTimeSet:(ret = 0)
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
----------------------------send status to monitor = 0
-----------------pid:0-------------
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
Main bssid = 40:9b:cd:60:62:fb
<==== rt28xx_init, Status=0
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
WiFi Startup Cost (ra0): 4.316s
------------------------------------------kernel monitor id=566
Raeth v3.1 (Tasklet,SkbRecycle)
phy_tx_ring = 0x005ef000, tx_ring = 0xa05ef000
phy_rx_ring0 = 0x005f0000, rx_ring0 = 0xa05f0000
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
RT305x_ESW: Link Status Changed
device eth2 entered promiscuous mode
device ra0 entered promiscuous mode
AddTxSType: already registered TxSType (PID = 32, Format = 0
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering forwarding state
restart mdns...
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
led=13, on=4000, off=1, blinks,=1, reset=1, time=4000
Jan 1 00:00:22 mDNSProxyResponderPosix: mDNSCoreReceiveResponse: Received from 192.168.0.50:5353 15 50.0.168.192.in- addr.arpa. PTR dlinkap.local.
Jan 1 00:00:22 mDNSProxyResponderPosix: mDNSCoreReceiveResponse: Unexpected conflict discarding 19 50.0.168.192.in-a ddr.arpa. PTR dlinkap62FA.local.
Jan 1 00:00:22 mDNSProxyResponderPosix: mDNS_Deregister_internal: Record 7FDCA554 not found in list 4 dlinkap62FA.l ocal. Addr 192.168.0.50
Jan 1 00:00:22 mDNSProxyResponderPosix: mDNS_Deregister_internal: Record 7FDCA8C0 not found in list 19 50.0.168.192. in-addr.arpa. PTR dlinkap62FA.local.
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
Stopped WatchDog Timer.
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
switch register base addr to system register 0xb0000000
write offset 0x60, value 0x55054450
write offset 0x654, value 0x6040
br0: port 1(ra0) entering forwarding state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
br0: port 1(ra0) entering forwarding state
led=11, on=5, off=5, blinks,=4000, reset=1, time=4000
led=37, on=5, off=5, blinks,=4000, reset=1, time=4000
init: can't log to /dev/tty5
starting pid 9002, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2018-05-08 16:57:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
Premendo il tasto 2 durante l'avvio ?? possibile effettuare il downgrade del firmware tramite TFTP.
Ho testato anche il flash del firmware russo, tutto funziona perfettamente ma ?? necessario effettuare il reset dopo l'aggiornamento.
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Feb 21 2017 Time:10:58:24
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!DRU DAP-1320
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.0.50) ==:10.10.10.123
Input server IP (192.168.0.180) ==:10.10.10.3
Input Linux Kernel filename () ==:test.bin
NetTxPacket = 0x83FE5E00
KSEG1ADDR(NetTxPacket) = 0xA3FE5E00
ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'test.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Got ARP REPLY, set server/gtwy eth addr (00:1f:16:ae:1d:24)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############
done
Bytes transferred = 5389206 (523b96 hex)
LoadAddr=82000000 NetBootFileXferSize= 00523b96
..................................................................................
..................................................................................
.
.
Done!
