Menu principale

DHP-1565: Router Wireless N PowerLine Gigabit

Aperto da Carciofone, 25 Aprile 2012, 08:29:14

Carciofone

DHP-1565: Router Wireless N PowerLine Gigabit



Due prodotti in uno: Router wireless N Gigabit e adattatore PowerLine AV 500 incorporati
- Tecnologia Wireless N: velocità wireless massima di 300 Mbps
- Velocità di trasferimento dati pari a 500 Mbps sulla rete elettrica esistente
- Crittografia mediante pulsante per proteggere la rete dalle intrusioni
- Porte Gigabit per massime velocità in modalità cablata
- Modalità AP per la connessione wireless e di fino a 4 dispositivi cablati alla rete, in modo da poter ampliare la propria rete più di quanto sia mai stato possibile
- Motore Quality of Service (QoS) per l'assegnazione delle priorità alle applicazioni sensibili ai ritardi (ad esempio streaming multimediale, videoconferenza)
- Maggiore resistenza alle interferenze elettriche
- Interoperabile: conforme allo standard IEEE 1901
- Compatibilità retroattiva con i prodotti PowerLine AV
- D-Link Green™: design a risparmio energetico
Utilizzare la rete elettrica di casa come rete ad alta velocità
Il router Wireless N PowerLine Gigabit utilizza la rete elettrica di casa vostra per espandere la rete in ogni angolo della vostra abitazione, con velocità fino a 500 Mbps. Basterà semplicemente collegare il DHP-1565 a qualsiasi presa a muro presente in casa per estendere la rete a qualsiasi adattatore PowerLine collegato a qualunque altra presa a muro dell'abitazione. Ciò vi consentirà di estendere la vostra rete fino a raggiungere posti in cui non è possibile far passare nuovi cavi (come garage o rimesse) o in cui il segnale wireless non è sufficientemente forte. Le tecnologie Wireless N e PowerLine si completano a vicenda per creare un'unica soluzione domestica tale da consentire di sbarazzarvi del disordine dei cavi!
Ideale per usi intensivi della larghezza di banda
Il router Wireless N PowerLine Gigabit è in grado di offrire velocità massime di trasferimento dati via cavo pari a 500 Mbps. Ciò lo rende ideale per gli usi intensivi della larghezza di banda, garantendo la massima uniformità e l'assenza di ritardi durante lo streaming di video HD, le chiamate VoIP e i giochi online. La tecnologia avanzata integrata in questo router lo rende più resistente alle interferenze elettriche delle altre apparecchiature domestiche, permettendo agli utenti di ottenere le massime velocità di trasmissione. In aggiunta, il motore Quality of Service (QoS) di cui è provvisto assegna la priorità al traffico Internet, garantendo l'assenza di intoppi nelle applicazioni multimediali quando si naviga sul Web o si eseguono download. DHP-1565 offre una larghezza di banda di rete estesa, che permette agli utenti della casa digitale di utilizzare la rete elettrica esistente per streaming multimediale di alta qualità.
Funzioni di router o Access Point
DHP-1565 può essere utilizzato in modalità router o Access Point semplicemente premendo l'interruttore sul retro del dispositivo. In modalità router, si connette al vostro modem cablato o DS per condividere la connessione Internet tramite Wi-Fi, Ethernet oppure utilizzando la vostra rete elettrica, rendendo necessario soltanto un adattatore PowerLine aggiuntivo per creare una connessione. In modalità Access Point, DHP-1565 funziona come un adattatore Wireless N PowerLine per estendere la rete domestica tramite un altro adattatore PowerLine connesso al router esistente. In questa modalità, è possibile connettere simultaneamente alla rete domestica fino a 4 dispositivi cablati in qualsiasi punto della casa, consentendovi di ampliare la vostra rete più di quanto sia mai stato possibile.
Compatibilità
Basato sulla tecnologia leader di settore PowerLine Alliance, il router Wireless N PowerLine Gigabit è compatibile con i dispositivi basati sullo stesso standard IEEE 1901, quali l'adattatore di rete e lo Starter Kit PowerLine AV 500 (DHP-500AV/-501AV) e l'adattatore di rete e lo Starter Kit PowerLine Passthrough AV 500 (DHP-P500AV/-P501AV). Esso è inoltre compatibile con i dispositivi che implementano lo standard precedente PowerLine AV, quali l'adattatore di rete e lo Starter Kit PowerLine AV (DHP-306AV/-307AV), l'adattatore di rete e lo Starter Kit PowerLine AV Passthrough (DHP-P306AV/-P307AV) e l'Extender e Starter Kit PowerLine AV Wireless N (DHP-W306AV/-W307AV) di D-Link.
Supporto del protocollo IPv6
Questo router è pronto per l'Internet del futuro grazie alla compatibilità con il passaggio da IPv4 a IPv6 che avverrà a breve. Il router presenta il logo dorato ""IPv6 Ready"" e garantisce così sia il supporto del protocollo IPv6 che la compatibilità con apparecchiature IPv6 di altri produttori. DHP-1565 è in grado di gestire il routing per le reti sia IPv4 che IPv6 simultaneamente, garantendo la compatibilità futura e retroattiva del router in uso.
Risparmia energia con D-Link Green
Il router Wireless N PowerLine Gigabit fa parte di D-Link Green, il programma di D-Link finalizzato alla distribuzione di prodotti ecologici senza rinunciare alle prestazioni. DHP-1565 supporta funzioni quali lo strumento di pianificazione WLAN, PowerLine stand-by e Green Ethernet. Lo strumento di pianificazione WLAN consente di impostare quando si desidera spegnere la rete wireless per risparmiare energia e migliorare la sicurezza. PowerLine stand-by interrompe la connessione PowerLine quando non viene rilevata alcuna attività. Green Ethernet offre ulteriori risparmi inserendo le porte Ethernet in modalità sleep e rilevando automaticamente la lunghezza dei cavi Ethernet connessi alle porte al fine di fornire solamente la giusta quantità di alimentazione.

Specifiche tecniche

Minimum system requirement (for D-Link Click'n'Connect)
   Windows®, Macintosh, or Linux-based operating system
   CD-ROM drive
   Ethernet adapter
   Internet Explorer 6 or later, Firefox 3.0 or later, Safari 3.0 or later, or Google Chrome 2.0 or later

Device management
   Web UI
   SharePortTM Plus
   UPnPTM AV Media Server
   Web File Access

Standards
   IEEE 802.11n
   IEEE 802.11g
   IEEE 802.11b
   IEEE 802.3u
   IEEE 1901
   HomePlug AV

Advanced firewall features
   Network Address Translation (NAT)
   Stateful Packet Inspection (SPI)
   VPN Pass-Through/Multi-Sessions
   PPTP/L2TP/IPSec

Device interfaces
   Gigabit WAN (RJ-45)
   Four Gigabit LAN (RJ-45)
   USB 2.0

Wirelesss frequency range
   2.4 GHz to 2.4835 GHz

Data Rates
   Powerline: up to 500 Mbps1
   802.11n: up to 300 Mbps2

Antennas
   Two internal 2 dBi antennas

Security
   64/128-bit WEP
   WPA & WPA2 (Wi-Fi Protected Access)

SharePort™ function support
   External hard drive
   multifunction USB printer

LED Status Indicators
   Power
   Internet
   Powerline

Power
   100 V to 240 V

Power Consumption
   Max. 12 W

Informazioni:
Broshure caratteristiche: DOWNLOAD

Carciofone

#1
Downloads:
Firmware:
Aggiornamento firmware 1.03B01 WW del 01.04.2013 DOWNLOAD (Molto lunga la lista dei bugfix successivi alla versione 1.00B35, per un upgrade assolutamente consigliato!)

Firmware DHP-1565 1.00B35: DOWNLOAD
Firmware DHP-1565 1.00B28: DOWNLOAD


Manuali:
Manuale EU (Eng): DOWNLOAD
Guida rapida: DOWNLOAD


Nuove versioni di Shareport Plus:
- per Windows: 4.11
- per MacOS: 1.0.7; 1.0.8

Carciofone

#2
...

Carciofone

...

SAKAMOTO70

Salve a tutti.
Credo di essermi incasinato.
Ho acquistato un dhp-1565 credendo di poterlo usare oltre che come punto di partenza per una rete power line, anche come router da sostituire al mio router DSL 2740-R.
Ho inoltre acquistato un W306AV per estendere il segnale al piano inferiore dove il segnale è scadente o assente.
Problema:
-come dispongo i 3 apparecchi in modo ottimale e/o cosa eventualmente eliminare?
-come configurali (esiste una guida dalla base)? ho provato ma gli apparecchi non comunicano con il pc.
-IP statico si intende per il 4 o per il 6?
Vi sarei grato per qualsiasi informazione

alebra

Citazione di: SAKAMOTO70 il 15 Gennaio 2013, 15:43:54Salve a tutti.
Credo di essermi incasinato.
Ho acquistato un dhp-1565 credendo di poterlo usare oltre che come punto di partenza per una rete power line, anche come router da sostituire al mio router DSL 2740-R.
Ho inoltre acquistato un W306AV per estendere il segnale al piano inferiore dove il segnale è scadente o assente.
Problema:
-come dispongo i 3 apparecchi in modo ottimale e/o cosa eventualmente eliminare?
-come configurali (esiste una guida dalla base)? ho provato ma gli apparecchi non comunicano con il pc.
-IP statico si intende per il 4 o per il 6?
Vi sarei grato per qualsiasi informazione

Ciao Sakamoto.
Anche io ho acquistato questo prodotto, abbinandolo a un adatatore AV500 passthrough, e mi sono arrivati oggi.
Un paio di anni fa avevo acquistato una coppia di prodotti powerline della Lynksys (cisco) a 200 Mbps e che ero riuscito a mettere in funzione in un paio di minuti.Così non è stato con questo prodotto che mi ha deluso un po', almeno in fase di installazione.
Anche la velocità di download è immutata (all'inizio era lento, anche se ora raggiungo circa i 620-650 kB7sec, cioè il valore che raggiungevo prima; con un solo pc collegato alla rete).
Per ora devo vedere come:
1- vedere la stampante collegata via USB (uno dei motivi per cui l'ho preso);
2-farlo comunicare con i Linksys a 200Mbps, che dovrebbero essere compatibili; se non ce la farò mi venderò la coppia che funziona benissimo e mi comprerò un a ltro adatttore come l'AV500.
Ripeto, finora sono andato a naso, come ho sempre fatto senza grandi problemi, anche per i settaggi del router NETGEAR che avevo fino a stamattina (che ha sempre funzionato PERFETTAMENTE per sei-sette anni, e che ho temporaneamente dismesso sperando in questo nuovo prodotto).
Tenamoci in contatto e speriamo di nn dover fare da cavie.
Ciao.

alebra

Citazione di: SAKAMOTO70 il 15 Gennaio 2013, 15:43:54Salve a tutti.
Credo di essermi incasinato.
Ho acquistato un dhp-1565 credendo di poterlo usare oltre che come punto di partenza per una rete power line, anche come router da sostituire al mio router DSL 2740-R.
Ho inoltre acquistato un W306AV per estendere il segnale al piano inferiore dove il segnale è scadente o assente.
Problema:
-come dispongo i 3 apparecchi in modo ottimale e/o cosa eventualmente eliminare?
-come configurali (esiste una guida dalla base)? ho provato ma gli apparecchi non comunicano con il pc.
-IP statico si intende per il 4 o per il 6?
Vi sarei grato per qualsiasi informazione
Premetto che non sono un tecnico o un superesperto, mi ritengo un praticone che sa la cava.
Due risposte più pertinenti:
Se non vuoi telefonare solo via Internet (VOIP), per mantenere la linea telefonica di casa ho collegato il 1565 al modem che mi ha fornito il provider (Tim, Vodafone, Tiscali ecc; per te il tuo DSL 2740-R che credo sia router e ANCHE MODEM, cioè è quello che riceve il segnale dalla rete)
collegandolo tramite la porta "Internet";
l'adattatore AV500 è in un'altra stanza e via rete elettrica si connette automaticamente , anche se non immediatamente.
Il tuo computer lo puoi collegare direttamente al 1565 (alla porta 1, per laprecisione) oppure all'adattatore (l'AV500 nel mio caso, il W306AV nel tuo, anche se quella W mi fa pensare ad un extender wireless, cioè non so se ha la porta LAN, magari ti colleghi wireless con quest'ultimo).
Il problema sono gli indirizzi della tua sub-rete che devono essere "superiori" a quela di base: cioè se cambi l'indirizzo di base (cosa auspicabile per sicurezza) in  192.168.100.100 gli altri devono essere per esempio 192.168.100.101.
Col Netgear l'intervallo della rete es. da 192.168.100.100 a 192.168.100.110 andava stabilito sul MODEM e bisognava DISABILITARE IL DHCP SUL NETGEAR (cioè sul D-LINK 1565), entrando nei settaggi del router via cavo: apri il browser e digiti http://192.168.0.1, che è l'indirizzo di default di quasi tutti i router venduti, poi navighi nei menu e ti regoli.
- l'IP statico è MEGLIO NON AVERLO se non hai esigenze aziendali (cioè di collegarti dall'esterno) perché rende più "identificabile e vulnerabile" la tua rete, anche se chi è capace buca tutto.
- poi potrai compiere atre azioi per la sicurezza come inserire i solo MAC address delle periferiche che vuoi abilitare (anche questo però è aggirabile).
Cambia subito password e nomi di default.
Spero di esserti stato di aiuto. Ciao

Carciofone

Ben arrivati nel forum.
Il DHP-1565 offre possibilità multiple di configurazione. La modalità ottimale di funzionamento è quella in cui esso fa da router e non da semplice AP (in pratica replica le funzioni di una DHP-W306AV). La si seleziona mediante l'interruttore meccanico posteriore presente sullo chassis.
Una volta fatto ciò il consiglio primario è quello di aggiornare il firmware del dispositivo alla versione 1.01 il cui link trovate nel terzo post.
Completato l'aggiornamento, esso va configurato esattamente come un qualsiasi router DIR con porta WAN connesso alla rete internet mediante un modem ADSL ethernet, il quale ultimo va configurato come spiegato qui a seconda del proprio provider: https://www.dlink-forum.it/index.php?topic=206.0
Il vecchio modem\router vedrà quindi disabilitate le proprie funzioni di routing\dhcp\wireless\firewall ... che saranno integralmente gestite dal DHP-1565.

Quanto al DHP in sè andrà configurato con connessione PPPoE (con username e password) oppure con DHCP lato WAN attivo a seconda dei casi (mancato supporto alla modalità Pure bridge PPPoA del vecchio modem).
Quanto alla configurazione della funzione Powerline il consiglio è quello di effettuare il tutto in modalità hardware configurando per prima la crittografia AES su una delle DHP-500AV o 300AV e poi effettuando il paring con il router. Il manuale è molto chiaro sulla procedura. Comunque consigli pratici per non sbagliare si trovano qua: https://www.dlink-forum.it/index.php?topic=655.msg8410#msg8410
(resettare la plc singola senza che nessun'altra sia connessa alla rete elettrica\premere il tasto di configurazione della sicurezza (Pair) del dispositivo per 3 sec. Il LED Power comincerà a lampeggiare generando una password privata casuale che servirà a configurare tutti gli altri\attendere che il led diventi acceso fisso (30-90 sec a seconda del modello)\connettere il 1565 alla linea elettrica\premere il tasto pair per 3 sec sul DHP-500AV\premere il tasto pair del 1565 sul lato posteriore del router\verificare che dopo qualche secondo i led link dei due dispositivi si accendano fissi (colore verde, arancio o rosso a seconda della velocità del link; led spento assenza di collegamento).
Come spiegato nelle guide linkate sopra, le versioni AV200 Mbit di D-Link sono sì compatibili con le 500, ma NON prendono (nei miei test) la crittografia da queste ultime, mentre configurando come master una DHP-300AV e poi le 500AV allora funziona tutto regolarmente.
Quindi ne dedurrei che con plc di altre marche:
1) non ci si possa aspettare che così come sono, tirandole fuori dalla scatola, si colleghino le une con le altre;
2) l'uso di utility diventa inutile, dato che probabilmente l'utility di un produttore non configura le plc di altro produttore;
3) il pair deve essere fatto solo via hardware per vedere se funziona;
4) impostate tutti i dispositivi con shell di configurazione avanzata perchè non usino indirizzamento ipv6, ma solo a livello locale, perchè tra modelli di vari produttori l'implementazione non è al 100% e rischiate di non trovare poi i dispositivi nella vostra rete.

Altro consiglio: procedete alla configurazione per gradi successivi e ricordate di impostare sul router che usate come modem un indirizzo IP diverso rispetto a quello del DHP-1565 (as es. 10.0.1.1, snmk 255.0.0.0).

alebra

Citazione di: C@rciofone il 16 Gennaio 2013, 07:58:29Ben arrivati nel forum.
Il DHP-1565 offre possibilità multiple di configurazione. La modalità ottimale di funzionamento è quella in cui esso fa da router e non da semplice AP (in pratica replica le funzioni di una DHP-W306AV). La si seleziona mediante l'interruttore meccanico posteriore presente sullo chassis.

Già configurato come router

Citazione di: C@rciofone il 16 Gennaio 2013, 07:58:29Una volta fatto ciò il consiglio primario è quello di aggiornare il firmware del dispositivo alla versione 1.01 il cui link trovate nel terzo post.
Completato l'aggiornamento, esso va configurato esattamente come un qualsiasi router DIR con porta WAN connesso alla rete internet mediante un modem ADSL ethernet, il quale ultimo va configurato come spiegato qui a seconda del proprio provider: https://www.dlink-forum.it/index.php?topic=206.0
Il vecchio modem\router vedrà quindi disabilitate le proprie funzioni di routing\dhcp\wireless\firewall ... che saranno integralmente gestite dal DHP-1565.

Ne prendo atto e cambierò il settaggio del modem Tiscali, prima le richieste erano diverse.
La cosa strana, secondo me, è che il modem continua a essere settato come 192.168.100.100 col DHCP abilitato con un range di intervalli  tipo  da 192.168.101 a 192.168.100.110 (per fare un esempio), mentre il DLink funziona lo stesso pur rimanendo a 192.168.0.1 anche lui col DHCP abilitato.
Ripeto di non essere un esperto, ma secondo me questo non dovrebbe essere impossibile, boh!

Citazione di: C@rciofone il 16 Gennaio 2013, 07:58:29Quindi ne dedurrei che con plc di altre marche:
1) non ci si possa aspettare che così come sono, tirandole fuori dalla scatola, si colleghino le une con le altre;
2) l'uso di utility diventa inutile, dato che probabilmente l'utility di un produttore non configura le plc di altro produttore;
3) il pair deve essere fatto solo via hardware per vedere se funziona;
4) impostate tutti i dispositivi con shell di configurazione avanzata perchè non usino indirizzamento ipv6, ma solo a livello locale, perchè tra modelli di vari produttori l'implementazione non è al 100% e rischiate di non trovare poi i dispositivi nella vostra rete.

Altro consiglio: procedete alla configurazione per gradi successivi e ricordate di impostare sul router che usate come modem un indirizzo IP diverso rispetto a quello del DHP-1565 (as es. 10.0.1.1, snmk 255.0.0.0).

Oggi, misteriosamente visto che non ho fatto alcunché di nuovo, i due dispositivi Linksys da 200 Mbps sono visti dal dhl1565. Ho provato un paio di download sui due device "vecchi" in due sanze diverse (XP sp3) e scaricava dai 500 ai 600 Mbit/sec. Per me sono valori buoni visto che ho una ADSL da  Mega (teorici, in realtà il router mi dà valori sui 6,2-6,4), anche se pensavo che avrei aumentato più significativamente passando al nuovo impianto.
Ora sono collegato via AV500 e l'utility di DLink mi dà valori di:
1- 500 Mbps,  3 tacche per la qualità
(il mio computer tramite AV 500 attività: Internet);
2- 200 Mbps,  3 tacche per la qualità
(il router 1565, attività: router con wireless attivato, se mi ricordo bene)
3- 150 Mbps,  3 tacche per la qualità
(computer figlio tramite Linksys a 200 Mbps, attività: gioco leggero online)
4- 57 Mbps,  1 tacca per la qualità
(computer figlia tramite Linksys a 200 Mbps, attività: Facebook e/o Youtube).
Sono valori buoni o no, viste le caratteristiche della mia ADSL ed il fatto che siamo colegati simultaneamente?
Credo di aver capito (con un certo ritardo) che i 500 Mbps si potrebbero raggiungere abbinando powerline e wireless SIMULTANEAMENTE, ma COME SI FA?
Se le cose stanno così mi interessano fino a un certo punto, visto che il mio intento era di ELIMINARE IL WIRELESS DA CASA ed AUMENTARE LE PRESTAZIONI COMPLESSIVE.
Ma perchè non fanno TUTTI questi device con un interruttore che possa disinserire il wireless? Cosa gli costa, 5 euro?

Ieri, sul computer di mio figlio (il computer da gioco via Internet, ecco la ragione dell'acquisto) l'AV500 dopo un iniziale collegamento NON ERA NEMMENO VISTO DAL COMPUTER (ora vi ho ricollegato il Linksys che aveva prima e il tutto funziona).
Forse devo seguire la procedura indicata di reinizializare il tutto partendo dall'AV500.
Saluto, ringrazio per i suggerimenti e nei prossimi giorni cercherò di capire bene se la spesa vale l'impresa (anche il 1565 l'ho pagato meno di 90 Euro, ed avevo l'esigenza di un print server).

Se non vedrò miglioramenti significativi sul piano gaming mi avvalerò del diritto di recesso e comprerò una VGA o una CPU migliori aggiungendo qualche Euro.
Ancora saluti a tutti.

Carciofone

Riguardo alla connessione, i router hanno due diversi dhcp: quello lato WAN che prende l'ip dal provider o dal modem ethernet, e quello lato lan sul lato interno della rete. Se tieni attivo il dhcp del modem tiscali ovviamente attiverai l'opzione perchè il router prenda l'ip automaticamente da quello, ma così rallenti la connessione perchè navigherai tramite due router con funzioni di firewall, routing etc attive contemporaneamente. La soluzione migliore sarebbe la pppoe bridge sul tiscali e pppoe con user e pass sul router, altrimenti vedi anche se il tiscali consente pppoa pure bridge oppure la chiamano anche bridge pppoa vc o qualcosa del genere a seconda dei modelli.

Il nuovo firmware è sensibilmente più prestante.

Se usi una rete mista di 500AV e 200Av, ovviamente tutte avranno le prestazioni delle 200AV per chè per compatibilità non vengono usate nè le frequenze aggiuntive, nè la compressione dati.

Quando parli di plc che misteriosamente si vedono mi par di capire che non sono configurate (cioè non sono assegnate a un gruppo di lavoro nè hanno una password loro e crittografia aes attiva. Quindi a volte si vedranno ed altre no, a seconda di come sarà la situazione di accensione, se ci sono altre plc in uso nel tuo palazzo etc ...

Sulle velocità delle plc tieni presente che la più veloce adsl sul mercato consumer arriva a 20 Mbit, se due plc sono anche collegate a 50 Mbit hai due volte e mezza banda disponibile per la navigazione. Per altri usi ovviamente la cosa è da valutare.
Segui magari i suggerimenti delle discussioni sulle plc per ottenere il massimo isolandole dai disturbi mediante prese filtrate per gli altri apparati.

SAKAMOTO70

Citazione di: C@rciofone il 16 Gennaio 2013, 07:58:29Ben arrivati nel forum.
Il DHP-1565 offre possibilità multiple di configurazione. La modalità ottimale di funzionamento è quella in cui esso fa da router e non da semplice AP (in pratica replica le funzioni di una DHP-W306AV). La si seleziona mediante l'interruttore meccanico posteriore presente sullo chassis.
Una volta fatto ciò il consiglio primario è quello di aggiornare il firmware del dispositivo alla versione 1.01 il cui link trovate nel terzo post.
Completato l'aggiornamento, esso va configurato esattamente come un qualsiasi router DIR con porta WAN connesso alla rete internet mediante un modem ADSL ethernet, il quale ultimo va configurato come spiegato qui a seconda del proprio provider: https://www.dlink-forum.it/index.php?topic=206.0
Il vecchio modem\router vedrà quindi disabilitate le proprie funzioni di routing\dhcp\wireless\firewall ... che saranno integralmente gestite dal DHP-1565.

Quanto al DHP in sè andrà configurato con connessione PPPoE (con username e password) oppure con DHCP lato WAN attivo a seconda dei casi (mancato supporto alla modalità Pure bridge PPPoA del vecchio modem).
Quanto alla configurazione della funzione Powerline il consiglio è quello di effettuare il tutto in modalità hardware configurando per prima la crittografia AES su una delle DHP-500AV o 300AV e poi effettuando il paring con il router. Il manuale è molto chiaro sulla procedura. Comunque consigli pratici per non sbagliare si trovano qua: https://www.dlink-forum.it/index.php?topic=655.msg8410#msg8410
(resettare la plc singola senza che nessun'altra sia connessa alla rete elettrica\premere il tasto di configurazione della sicurezza (Pair) del dispositivo per 3 sec. Il LED Power comincerà a lampeggiare generando una password privata casuale che servirà a configurare tutti gli altri\attendere che il led diventi acceso fisso (30-90 sec a seconda del modello)\connettere il 1565 alla linea elettrica\premere il tasto pair per 3 sec sul DHP-500AV\premere il tasto pair del 1565 sul lato posteriore del router\verificare che dopo qualche secondo i led link dei due dispositivi si accendano fissi (colore verde, arancio o rosso a seconda della velocità del link; led spento assenza di collegamento).
Come spiegato nelle guide linkate sopra, le versioni AV200 Mbit di D-Link sono sì compatibili con le 500, ma NON prendono (nei miei test) la crittografia da queste ultime, mentre configurando come master una DHP-300AV e poi le 500AV allora funziona tutto regolarmente.
Quindi ne dedurrei che con plc di altre marche:
1) non ci si possa aspettare che così come sono, tirandole fuori dalla scatola, si colleghino le une con le altre;
2) l'uso di utility diventa inutile, dato che probabilmente l'utility di un produttore non configura le plc di altro produttore;
3) il pair deve essere fatto solo via hardware per vedere se funziona;
4) impostate tutti i dispositivi con shell di configurazione avanzata perchè non usino indirizzamento ipv6, ma solo a livello locale, perchè tra modelli di vari produttori l'implementazione non è al 100% e rischiate di non trovare poi i dispositivi nella vostra rete.

Altro consiglio: procedete alla configurazione per gradi successivi e ricordate di impostare sul router che usate come modem un indirizzo IP diverso rispetto a quello del DHP-1565 (as es. 10.0.1.1, snmk 255.0.0.0).

Grazie ai tuoi consigli sono riuscito a configurare correttamente i tre apparecchi modem/router-dhp1565-W306AV.
In un paio di giorni ho potuto testarli su diversi apparecchi (tv-tablet-smartphone) con un buon grado di soddisfazione.
La mia impressione da profano e che:
-il dhp1565 poteva essere pensato anche come modem
-gli apparecchi andrebbero venduti con firmware aggiornato (si     risparmierebbe tempo e fatica)
-dlink potrebbe anche pensare di fare un manuale completo anche in italiano.
Oggi ho comunque acquistato un terzo elemento il dhp-p500av e mi dico.
ormai non avro piu problemi per configurarlo e invece...
 Come prima mossa vado ad aggiornare il firmware ma anche in questo caso risulta un'operazione difficoltosa in quanto la chiave per scompattare il file non si trova.
Dopo un po intuisco che posso ottenerla con l'utility ma anche questa presenta dei problemi ... non funziona.
Nel frattempo mi accorgo che il W306AV era stato resettato dalla presenza in rete del p500av.
Purtroppo ho dovuto interrrompere. Domani ricomincio.
Forse avrei fatto prima a passare i cavi

Alby

Per la P500AV il firmware da mettere se vuoi aggiornare e se non ne ha uno di già aggiornato è l'1.02, non l'1.03 che disabilita lo standby (per usi particolari in cui serve che la plc non vada in standby).
Ne parliamo qui: https://www.dlink-forum.it/index.php?topic=908.0 https://www.dlink-forum.it/index.php?topic=908.msg22097#msg22097
1) Utility del sito tedesco: Download
2) firmware 1.02: Download

Per la configurazione di una plc aggiuntiva sulla rete powerline segui i consigli che ci sono qui: https://www.dlink-forum.it/index.php?topic=1582.msg7733#msg7733
Per aggiungere un'unità alla rete ce ne deve essere solo un'altra collegata e non deve essere in uso da parte di un pc altrimenti non trasmette il codice crittografico.
Anche della W306AV c'è un firmware aggiornato 1.03 EU.

Ovviamente i firmware di questi apparati sono aggiornabili per logiche ragioni legate alle normative in continuo aggiornamento e ai diversi mercati. Se la GB vieta l'uso di certe frequenze radio per le interferenze che provocano sulle eliambulanze, serve un nuovo firmware che limiti le plc impedendo di emettere onde radio tramite l'impianto elettrico, come pure se il prodotto nasce con standard teorici per essere usato su una linea elettrica a 125V, poi magari si vede che sul 220 conviene fare delle modifiche etc ... (tra l'altro non tutte le plc che arrivano sul mercato italiano sono versioni per l'Italia e tramite il firmware si possono adattare).

Carciofone

Nuovo firmware per il DHP-1565 versione 1.03B01 WW del 1 aprile 2013.
Nel file è incluso un changelog parziale. Molte le novità e i bugfix.

DOWNLOAD.

Changelog:
Model DHP-1565 A1
Firmware Version 1.03b01
Date 2013-04-01

Fixed:
1. GUI issue, in AP mode the max year only can select to 2012.
2. If plug-in USB device with lot of files will cause DHP-1565 GUI crash.
3. DLNA discovery via DHP-500AV not work.
4. UPnP security issue.
5. Setup Wizard, set the timezone to +01:00 Amsterdam..the timezone in Tools -> Time page is -08:00.




DHP1565A1(Linux version) Firmware Release Note
Project Name: DHP-1565
HW version: A1
Region/OEM code: CEB
WLAN Domain: 0x37
Channel List: 2.4GHz: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13
5GHz: None
Firmware Query URL: http://wrpd.dlink.com.tw/router/firmware/query.asp?model=DHP-1565_Ax_Default
Flash size: 16MB
DRAM size: 128MB

======================================================================================
Firmware Version: ver1.01b13
Firmware Date: Fri, 20, Apr, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x908344F5
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 5468
APPS SVN Revision: 5468
APPS_CGI SVN Revision: 7115
WIRELESS SVN Revision: 114
PLATFORM SVN Revision: 337
ATHSDK SVN Revision: 100

Fixed:
        - In AP mode, WAN LED not bright when set static ip address.
======================================================================================
Firmware Version: ver1.01b12
Firmware Date: Thu, 19, Apr, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum:
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 5457
APPS SVN Revision: 5457
APPS_CGI SVN Revision: 7115
WIRELESS SVN Revision: 114
PLATFORM SVN Revision: 337
ATHSDK SVN Revision: 100

Fixed:
        - In AP mode, WAN LED not bright after DUT reboot(SW/HW) in AP mode.
======================================================================================
Firmware Version: ver1.01b11
Firmware Date: Thu, 19, Apr, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xA5CA3370
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision:  5445
APPS SVN Revision: 5445
APPS_CGI SVN Revision: 7115
WIRELESS SVN Revision: 114
PLATFORM SVN Revision: 337
ATHSDK SVN Revision: 100

Fixed:
- In AP mode, HomePlug LED always light-on
- In AP mode, WAN LED always light-on
======================================================================================
Firmware Version: ver1.01b10
Firmware Date: Thu, 15, Mar, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum:  0xDE889B58
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision:  4927
APPS SVN Revision: 4927
APPS_CGI SVN Revision: 7115
WIRELESS SVN Revision: 114
PLATFORM SVN Revision: 337
ATHSDK SVN Revision: 100

Fixed:
- When use Web UI restore to default in the AP mode,then the page will be change to the Router mode.

======================================================================================
Firmware Version: ver1.01b09
Firmware Date: Wed, 14, Mar, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xB52A0387
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4901
APPS SVN Revision: 4901
APPS_CGI SVN Revision: 7111
WIRELESS SVN Revision: 114
PLATFORM SVN Revision: 337
ATHSDK SVN Revision: 100

Fixed:
- TSDBug:11078 Storage Page was gone after restore to factory default
- TSDBug:10104 BT Endurance Stress Test
- L2TP On-demand can't trigger
- DLNA + Storage can't display file(mp3 or jpg ) in the medial player(win7)

======================================================================================
Firmware Version: ver1.01b08
Firmware Date: Thu, 8, Mar, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x36333AEB
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4797
APPS SVN Revision: 4797
APPS_CGI SVN Revision: 7104
WIRELESS SVN Revision: 109
PLATFORM SVN Revision: 334
ATHSDK SVN Revision: 98

1. Fixed
- TSDBug 10275: When L2TP is connected,web GUI will be able to login until WAN cable is unplugged.
- TSDBug 10302: Status-wireless page is failed show connected wireless clinet on IE
- TSDBug 10376: Enable/Disable "True Gigabit Routing Connectivity" will cause DUT crashed
- TSDBug 10104: BT Endurance Stress Test
- TSDBug 10123: The DHCP-1565 doesn't make IPv6 communication over powerline
- TSDBug 10336: The MP3, JPEG or files with Chinese file name are not seen by Media player.
- TSDBug 10335: Storage user permission issues.
- TSDBug 10436: AP's LAN information doesn't show peoperly when wan type is pre-configured to PPPoE or PPTP or L2TP in Router Mode.
- TSDBug 10276: XBox 360 can not detect Media Server of DHP-1565
- TSDBug  6827: 802.1p QoS Test
- TSDBug 10488: WCN Setup
- Firmware size too large
======================================================================================
Firmware Version: ver1.01b07
Firmware Date: Wed, 7, Mar, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xED71FE0D
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4791
APPS SVN Revision: 4791
APPS_CGI SVN Revision: 7101
WIRELESS SVN Revision: 109
PLATFORM SVN Revision: 334
ATHSDK SVN Revision: 98

1. Fixed
- TSDBug 10275: When L2TP is connected,web GUI will be able to login until WAN cable is unplugged.
- TSDBug 10302: Status-wireless page is failed show connected wireless clinet on IE
- TSDBug 10376: Enable/Disable "True Gigabit Routing Connectivity" will cause DUT crashed
- TSDBug 10104: BT Endurance Stress Test
- TSDBug 10123: The DHCP-1565 doesn't make IPv6 communication over powerline
- TSDBug 10336: The MP3, JPEG or files with Chinese file name are not seen by Media player.
- TSDBug 10335: Storage user permission issues.
- TSDBug 10436: AP's LAN information doesn't show peoperly when wan type is pre-configured to PPPoE or PPTP or L2TP in Router Mode.
- TSDBug 10276: XBox 360 can not detect Media Server of DHP-1565
- TSDBug  6827: 802.1p QoS Test
- TSDBug 10488: WCN Setup
======================================================================================
Firmware Version: ver1.01b06
Firmware Date: Wed, 16, Feb, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x46678C38
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4621
APPS SVN Revision: 4621
APPS_CGI SVN Revision: 7076
WIRELESS SVN Revision: 102
PLATFORM SVN Revision: 330
ATHSDK SVN Revision: 98

1. Fixed
- DUT reboot caused by AR7400 no responding 10 seconds, because CPU too busy.
 We extends responding theshould to 50 seconds.
======================================================================================
Firmware Version: ver1.01b05
Firmware Date: Wed, 18, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x991AAB99
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4466
APPS SVN Revision: 4466
APPS_CGI SVN Revision: 6992
WIRELESS SVN Revision: 100
PLATFORM SVN Revision: 326
ATHSDK SVN Revision: 98

1. Fixed
- WPS Lock Function
- IPv6 simple security
 1) user can't access ipv6 https via lan side DUT
 2) remote user can't access ipv6/ipv4 http remote management
- UNH-1.06
 1.4) DUT can't query the second DNS server ipv6
 2.4) DUT user wrong source ip when query the second DNS server ipv6
 3.1) ipv6 system check can't work for wan/lan global ip address and link local address

2. Not a Bug
- Not support global address, ULA address notify for upnp6
======================================================================================
Firmware Version: ver1.01b04
Firmware Date: Wed, 11, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x19FC7A15
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4402
APPS SVN Revision: 4402
APPS_CGI SVN Revision: 6925
WIRELESS SVN Revision: 97
PLATFORM SVN Revision: 325
ATHSDK SVN Revision: 98

1. Feature
- Router Web File Access Specification v1.02
- D-Link Router IPv6 v1.20(Support UNH, and UPnP on IPv6)
- D-Link Router IPv6 v2.00(RFC6092 IPv6 Simple Security)
- D-Link Router IPv6 v2.01
 (UNH 1.00b6+Separate address provision flow + IPv6 Auto-Detection Enhancement)
- D-Link Router Web-based Setup Wizard v1.05

2. Fixed
- WPS Lock Function
======================================================================================
Firmware Version: ver1.01b03
Firmware Date: Tue, 27, Dec, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xE4A1F83E
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4217
APPS SVN Revision: 4217
APPS_CGI SVN Revision: 6832
WIRELESS SVN Revision: 85
PLATFORM SVN Revision: 317
ATHSDK SVN Revision: 98
 
1.Test
- support for DHNAP support (QRS mobile)
======================================================================================
Firmware Version: ver1.01b02
Firmware Date: Mon, 26, Dec, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x83D74BD5
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4202
APPS SVN Revision: 4202
APPS_CGI SVN Revision: 6823
WIRELESS SVN Revision: 85
PLATFORM SVN Revision: 316
ATHSDK SVN Revision: 98
 
1.Fixed
- Firmware version is wrong on status page and version.txt

======================================================================================
Firmware Version: ver1.01b01
Firmware Date: Fri, 21, Dec, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x3923402D
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4147
APPS SVN Revision: 4147
APPS_CGI SVN Revision: 6813
WIRELESS SVN Revision: 83
PLATFORM SVN Revision: 316
ATHSDK SVN Revision: 97

1. Fixed
- TSDBug 6699: PLC Utility display DUT's firmware version/date different from Web UI
- TSDBug 7283: DUT into power saving need 325-360sec over spec 300sec.
- TSDBug 7510: The fireware page dispay error when use Safari.
- TSDBug 7315: Idle time issue for DCC configure device.
- TSDBug 7625: DLNA Device Webpag can not be open and hyper link issue.
- TSDBug 7485: DCS2121(IP-CAM) can not connect to the DUT with wpa2aes
- Ethernet Type 0x88E1 broadcast to WLAN and LAN site.
- Use DCC Utility WAN LED Issue when pppoe connected.
- Support use http://dlinkrouterWXYZ access WEB UI,
 WXYZ should be latest 4 digits of PLC MAC, not LAN MAC.
======================================================================================
Firmware Version: ver1.00b33
Firmware Date: Wed, 18, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xEB7D0256
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4463
APPS SVN Revision: 4462
APPS_CGI SVN Revision: 4463
WIRELESS SVN Revision: 100
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Fixed Bug:
- WPS lock function issue
======================================================================================
Firmware Version: ver1.00b32
Firmware Date: Mon, 9, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xBD43C7D1
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4363
APPS SVN Revision: 4363
APPS_CGI SVN Revision: 4363
WIRELESS SVN Revision: 93
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Fixed Bug:
- WPS Lock function issue in DCC procedure
======================================================================================
Firmware Version: ver1.00b31
Firmware Date: Mon, 9, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x9C398E1C
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4351
APPS SVN Revision: 4349
APPS_CGI SVN Revision: 4351
WIRELESS SVN Revision: 93
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Fixed Bug:
- WPS Lock Function UI check
 1. Default, wireless wizard in wireless page
- Disable-PIN method will be disabled from enabled, when change wireless setting
======================================================================================
Firmware Version: ver1.00b30
Firmware Date: Mon, 9, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x41FB383F
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4337
APPS SVN Revision: 4337
APPS_CGI SVN Revision: 4337
WIRELESS SVN Revision: 93
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Fixed Bug:
- WPS Lock Function UI check
 1. Default, wan wizard and set wireless
 2. Default, wireless wizard in wireless page
- WPS Lock Function disable from enable mode-PIN & PBC function check and UI check
 1. PIN reconfiguration DUT
======================================================================================
Firmware Version: ver1.00b29
Firmware Date: Fri, 6, Jan, 2012
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x3194C4D4
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 4304
APPS SVN Revision: 4304
APPS_CGI SVN Revision: 4306
WIRELESS SVN Revision: 90
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Fixed Bug:
- WPS Lock Function
======================================================================================
Firmware Version: ver1.00b28
Firmware Date: Fri, 11, Nov, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xFCDBD040
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3715
APPS SVN Revision: 3715
APPS_CGI SVN Revision: 6691
WIRELESS SVN Revision: 68
PLATFORM SVN Revision: 298
ATHSDK SVN Revision: 91

1. Test
- Win7 Logo
- Wireless should have stable throughput in security mode

2. Fixed Bug:
- TSDBug 7428: after press the common connect button, the power LED spend 5sec begin to blink.
- TSDBug 6766: WAN packet do not fragment when packet length is 1425
- TSDBug 7483: The DUT icon doesn't match D-Link 404 page.
- TSDBug 6446: LAN PC can't use the device name to login the WEB UI.
- TSDBug 6631: Can't display status of IPv6(Status IP).
- TSDBug 6657: DUT can't display IPv6 address of status page.
- TSDBug 6524: Change setting cause GUI display incorrect issue.
      Change any settings then click "Save Settings" button,
      the web GUI can't be displayed.

3. Not Support:
- TSDBug 6827: 802.1p QiS function can not work,
      because when transmit VLAN Tag frame, DUT will remove VLAN Tag.
- TSDBug 6555: Can't bookmark it when using chrome or safari.
- TSDBug 6728: No IPv6 Firewall and IPv6 Routing help descriptions.
- TSDBug 6791: Guest zone client can access DUT when disable routing between zones.
- TSDBug 7431: Support menu issue, please reference the file.
- TSDBug 7402: HTTPS CA for Remote Management issue.
      Enable "Remote Management and HTTPS", then visit DUT Web GUI from WAN side, browser displayed CA incorrect.
======================================================================================
Firmware Version: ver1.00b27
Firmware Date: Mon, 24, Oct, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x7380610B
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3440
APPS SVN Revision: 3440
APPS_CGI SVN Revision: 6605
WIRELESS SVN Revision: 59
PLATFORM SVN Revision: 286
ATHSDK SVN Revision: 87

1. Test
- NAT Throughput
- Win7 Logo
- IGMP snooping wifi data rate

2. Fixed Bug:
- TSDBug 7003: enable guestzone routing between zones, the wireless client
 can't access router GUI via guestzone
- TSDBug 7034: when PLC utility display PHY rate 381 Mbps,
 but WEBUI of DHP-1565 only show 255 Mbps.
- TSDBug 6693: if user input "00:00:00:00:00:00" WAN MAC address
 in "Setup->Internet", it should recoved to default MAC address,
 and odd MAC prefix cannot be used.
- TSDBug 6582: RT Mode, WAN PPPoE and enable web access log 2 PCs, PC1 by IP, PC2 by MAC.
          PC1 log message is correct but PC2 log missing MAC address.
======================================================================================
Firmware Version: ver1.00b26
Firmware Date: Wed, 19, Oct, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x381CB47C
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3404
APPS SVN Revision: 3404
APPS_CGI SVN Revision: 6594
WIRELESS SVN Revision: 57
PLATFORM SVN Revision: 280
ATHSDK SVN Revision: 86

1. Feature
- PLC Power Saving Mode UI

2. Fixed Bug:
- TSDBug 6693: RT Mode, shouldn't allow "00:00:00:00:00:00" input for
 WAN MAC address in "Setup -> Internet"
- TSDBug 6530: RT Mode,firmware version display in "Setup->Wireless" not correct.
 It display "1.00NA", the version should br "1.00" and website filter "reject"
 message page has the same issue.
- TSDBug 6664: AP Mode, it should change the error message when
 push apply button in MAC filter.
- TSDBug 6525: RT Mode, wording issue for true gigabit routing connectivity settings.
 The word "Gibabit" should be modified to "Gigabit" in true gigabit routing connectivity settings.
- TSDBug 6582: RT Mode, WAN PPPoE and enable web access log 2 PCs, PC1 by IP, PC2 by MAC.
 PC1 log message is correct but PC2 log missing MAC address.
- TSDBug 6708: PLC, Power saving function can't work, after DUT lose link for 300sec.
- TSDBug 6734: RT Mode, QoS not work issue. Manual configured uplink speed,
 run uplink throughput test not work. The throughput value will higher then manual configure value.
- TSDBug 6619: AP Mode, It shouldn't use the default IP(ex: 192.168.0.50) to login page
 if user try to setting the static IP(192.168.1.50) in LAN settings.
- TSDBug 6796: DCC, when DUT securing powerline network connection was unsuccessful,
 DCC will display "Your Powerline network is secured"
- TSDBug 6797: IPv6, IPv6 auto detection PPPoE issue.
 Step1 Set IPv4 to PPPoE mode.
 Step2 Set IPv6 auto detection(PPP established).
 All other setting keep default value. Result LAN PC cannot access internet by IPv6 address.
- TSDBug 6730: PLC, when we add PLC member via WEBUI, it's always display error message about
 "PLC_KEY_INVALID" even input correct DKP and other PLC in the same group.
======================================================================================
Firmware Version: ver1.00b25
Firmware Date: Tue, 12, Oct, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x92C2968B
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3339
APPS SVN Revision: 3339
APPS_CGI SVN Revision: 6578
WIRELESS SVN Revision: 55
PLATFORM SVN Revision: 275
ATHSDK SVN Revision: 86


1. Feature:
- PLC Power Saving Mode

2. Fixed Bug:
- TSDBug 6727: Router mode, after configured router with DCC then link WEBUI,
      the setup wizard web-based page still be displayed.
- TSDBug 6709: Configured WAN type to PPTP/L2TP, Reconnect Mode select "Always on",
      manual disconnect PPTP/L2TP connection, it will auto-reconnect.
- TSDBug 6707: AP mode, if user input holomorphic characters, we couldn't login WEBUI.
- TSDBug 6702: Router mode, DUT WAN type configured as DHCP, after click "DHCP Release"
      button in "Status->Device Info" page, DUT will auto get IP without
      click "DHCP Renew" button.
- TSDBug 6699: PLC utility display DUT's firmware version different from WEBUI
- TSDBug 6693: Router mode, shouldn't allow "00:00:00:00:00:00" input for WAN MAC
      address in "Setup->Internet"
- TSDBug 6691: Router mode, the IP address in virtual server should be in LAN subnet
      not DHCP range, the message should be modified for IP address check.
- TSDBug 6681: Router mode, test result for anti-spoof checking enable and disable
      were the same, we couldn't verify this function work or not.
- TSDBug 6530: Router mode, firmware version display in "Setup->Wireless" not correct.
      It display "1.00NA", the version should be "1.00" and webite filter
      "reject" message page has the same issue.
- TSDBug 6677: Router mode, test with SIP ACG, SIP server at WAN side, LAN PC1 and PC3
      can't heard voice with each other.
- TSDBug 6667: AP mode, MAC filtering ON and ALLOW or DENY all fail
- TSDBug 6665: AP mode, it doesn't found the wireless client in the list of the MAC filter.
- TSDBug 6664: AP mode, it should change the error message when push apply button in MAC filter.
- TSDBug 6657/6631: AP mode, DUT can't display IPv6 address of status page.
- TSDBug 6578: AP mode, There are some wrong string in Setup Wizard.
- TSDBug 6555: AP mode, can't bookmark it when using chrome or safari.
- TSDBug 6553: AP mode, it should be check blank SSID in Setup Wizard.
- TSDBug 6546: AP mode, GUI still displayed before setting when running WPS configuration test.
- TSDBug 6428/6522: AP mode, it shouldn't show "NULL" when channel is auto mode.
- TSDBug 6532: Router mode, config WAN type "PPTP/L2TP" and reconnect mode "manual"
      then click "connect" button in status page, it can't connect to VPN server.
- TSDBug 6429: AP mode, the default device name doesn't match D-Link's spec.
- TSDBug 6446: AP mode, LAN PC can't use the device name to login the WEBUI.
- TSDBug 6447: AP mode, WEBUI should avoid the illegal character in device name.
- TSDBug 6521: Router mode, website filter list should allow empty issue.
- TSDBug 6525: Router mode, wording issue for true gigabit routing connectivity settings.
      The word "Gibabit" should br modified to "Gigabit" in
      true gigabit routing connectivity settings.
- TSDBug 6526: The internet session timeout time largest than description in support menu.
======================================================================================
Firmware Version: ver1.00b24
Firmware Date: Tue, 4, Oct, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x9887BD04
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3235
APPS SVN Revision: 3235
APPS_CGI SVN Revision: 6542
WIRELESS SVN Revision: 53
PLATFORM SVN Revision: 262
ATHSDK SVN Revision: 86

1. Fixed Bug:
BugNo:7199 WPS PBC LED(HW) keep blinking 120 seconds when WPS process in finish.
TSDBug: shouldn't allow user use LAN PC to telnet DUT with 23
======================================================================================
Firmware Version: ver1.00b23
Firmware Date: Tue, 20, Sep, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x4A685CA4
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 3069
APPS SVN Revision: 3069
APPS_CGI SVN Revision: 6478
WIRELESS SVN Revision: 50
PLATFORM SVN Revision: 229
ATHSDK SVN Revision: 82

1. Fixed Bug:
BugNo:7185 Schedule can be add and save without any days when select "select days"
BugNo:7183 Not follow [chklst.txt for MP update] v1.16
BugNo:7181 An error page in final countdown page of wizard in AP mode figure 1,
  and wizard loop will re-do again when try to login, if push wizard cancel
  above description and check wireless had be changed, but
  "reset to unconfigured" is grayed out
BugNo:7060 client set WEP with sharekey can't connect with DUT set WEP with both
BugNo:7009 PLC: scan list can't list all devices or list device repeat and
  should not list DUT device
BugNo:7165 WPS PBC (HW)__WPS PBC (HW) function is not function
BugNo:7166 WPS PBC LED (HW)__there is no WPS LED light. (WIN 7 LOGO would check LED)
======================================================================================
Firmware Version: ver1.00b22
Firmware Date: Wed, 14, Sep, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x7BF92F91
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2974
APPS SVN Revision: 2978
APPS_CGI SVN Revision: 6448
WIRELESS SVN Revision: 47
PLATFORM SVN Revision: 228
ATHSDK SVN Revision: 82

1. Fixed Bug:
BugNo:5927 Can't upload FW and show "upgrade failed" using chrome or safari on recovery mode
BugNo:6013 AP: DUT Mac address on recovery mode is different on normal
BugNo:6014 AP: Can't upload FW and show "upgrade failed" using chrome or safari on recovery mode
BugNo:6915 Wrong model name and FW version on PLC UI(DHP540 or DHP502)
BugNo:6988 D-Link Consumer AP Web UI Specification v1.05
BugNo:7060 client set WEP with Sharekey can't connect with DUT set WEP with both
BugNo:7125 Shareport - UI can see usb but can't open it.
BugNo:7128 there is no model name in plc UI
BugNo:7161 DUT must have the same MAC address on normal mode and recovery mode
BugNo:7162 Accroding to PLC LED SPEC from PM.
  - solid orange, during power on process,
  - blinking orange, DUT is under recovery mode
BugNo:7164 Setup wizard doesn't support the last version(D-Link Router Web-based Setup Wizard Specification v1.05)
BugNo:5987 WLAN with schedule is failed. Clients can't survey or connect with DUT when time is on schedule. v1.00B18,
  -->Fail (there are no schedule for AP Mode, RT mode is pass)
======================================================================================
Firmware Version: ver1.00b21
Firmware Date: Wed, 7, Sep, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x17CBB8F5
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2893
APPS SVN Revision: 2893
APPS_CGI SVN Revision: 6395
WIRELESS SVN Revision: 47
PLATFORM SVN Revision: 222
ATHSDK SVN Revision: 82

1. Fixed Bug:
BugNo:5928 Reset button on DUT is failed
BugNo:5985 DHCP client list would show other domain PC
BugNo:6002 AP: WPS function keep countdown and show connection failed
  while running WPS and client connect successful
BugNo:6103 button on status page should be gray out
  while DUT is connecting or disconnecting
BugNo:6190 RT: sometime web GUI can't access after setting something(WAN or setup wizard)
BugNo:6277 usually pop-up error message when access DUI GUI
BugNo:6303 can't use recovery mode, HW issue
BugNo:6309 Sometime icon wouldn't be shown. After set setup wizard.
BugNo:6366 the HWNAT function is workable but should wait a few minute
BugNo:7008 last PLC network group has disconnected
  when change new network name and click reboot later
BugNo:7009 scan list can't list all devices or list device repeat
  and should not list DUT device
BugNo:7011 member list information sometime would show wrong.
  List shows Link Rate is 0 and status is disconnect, but ping is ok.
BugNo:7115 Device usually crash
======================================================================================
Firmware Version: ver1.00b20
Firmware Date: Sat, 3, Sep, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x82F40D84
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2862
APPS SVN Revision: 2862
APPS_CGI SVN Revision: 6383
WIRELESS SVN Revision: 45
PLATFORM SVN Revision: 221
ATHSDK SVN Revision: 82

1. Feature
- DDNS Specification v1.06R-Draft
- Win7 Logo
- SharePort
- PLC QoS

2. Fixed Bug:
- BugNo:7114 D-Link Router Specification for 404 Error Pages; should link to Web UI when user click device icon.
    (D-Link Router Specification for 404 Error Pages v1.03)
- BugNo:7116 AP mode: WPS Web UI doesn't follow WPS_2.0_GUI_Change_Spec_Porting_Guide_v1.01
- BugNo:7063 "Enable IPv6 Multicast Streams" should be disabled by default. (Should be Enabled, please refer SPEC 1.19)
- BugNo:7062 D-Link Router Web-based Setup Wizard Specification v1.04R1;
    there are wrong string on setup wizard /password page when password contain ">".
- BugNo:7061 Decryption on rebooting page should not contain about changed the IP after change setting without LAN setting.
- BugNo:7060 client set WEP with sharekey can't connect with DUT set WEP with both
- BugNo:7058 WEBGUI would be re-directing to index page when DUT detect internet type on setup wizard
- BugNo:7052 warning message fail(AP mode doesn't support)
- BugNo:7012 Router mode: Copyright string should be white on login page.
- BugNo:7008 PLC: last PLC network group has disconnected when change new network name and click reboot later
- BugNo:6988 D-Link Consumer AP Web UI Specification v1.05
- BugNo:6973 Support DHCPv6 Release and Renew Button in IPv6 status page. (Autoconfiguration Mode)
    -->issue there are no buttons on AP mode. (AP Mode do not need to support Release/Renew button)
- BugNo:6950 IPv6 Spec 1.19 (ULA address would access internet on IPv6 PPPoE mode)
- BugNo:6181 wrong model name on step 4 in setup wizard.
- BugNo:6015 AP: Wrong icon on network map.
- BugNo:5992 (issue) bookmark URL should be http://dlinkap/
- BugNo:5988 if SSID contain of " then next step GUI would show incorrectly
- BugNo:5987 WLAN with schedule is failed, clients can't survey or connect with DUT when time is on schedule.
- BugNo:5984 error on status page

3. Test:
- BT session
======================================================================================
Firmware Version: ver1.00b19
Firmware Date: Fri, 26, Aug, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xE365E895
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2748
APPS SVN Revision: 2748
APPS_CGI SVN Revision: 6343
WIRELESS SVN Revision: 42
PLATFORM SVN Revision: 213
ATHSDK SVN Revision: 80

Fixed Bug
-BugNo.6949: wrong device icon on 404 error page
-BugNo.6181: wrong model name on step 4 in setup wizard
-BugNo.5929: Didn't support 404 error page
-BugNo.6988: D-Link Consumer AP Web UI Specification v1.05
-BugNo.6977: AP mode Timeout; APUT UI should not go to login page
    when UI idle 3 minutes on status/device info page.
-BugNo.6981: AP mode: wrong warning message when security set WEP or WPA-PSK.
-BugNo.7008: last PLC network group has disconnected when
    change new network name and click reboot later.
-BugNo.7010: manual add member is fail. Feedback always shows PLC_KEY_INVALID.
-BugNo.7051: support mmmm mmmm or mmmm-mmmm pin code for WPS
-BugNo.7053: If user set wifi with TKIP of cipher or WEP of security,
    the DUT will be disabled WPS and pop warning message.
-BugNo.7054: firmware query url on release note is different
    from chklst.txt or version.txt
-BugNo.7056: AP mode: Current PIN code would be empty
    after click "Reset PIN to Default" button.
-BugNo.7057: AP mode: Lost helpful hint on maintanance/system page.
-BugNo.7059: wireless information would be disappear on status page
    when enabled guest zone.
======================================================================================
Firmware Version: ver1.00b18
Firmware Date: Fri, 12, Aug, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xD95E7130
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2528
APPS SVN Revision: 2528
APPS_CGI SVN Revision: 6293
WIRELESS SVN Revision: 40
PLATFORM SVN Revision: 195
ATHSDK SVN Revision: 78

1. Feature :
- support setup wizard for ap mode by Spec 1.04R
- WPS 2.0 feature :
o. support mmmm mmmm or mmmm-mmmm pin code for WPS.
o. support 4-digits pin code.
o. warring message :
- If user set wifi with TKIP of cipher or WEP of security
, the DUT will be disabled wps and pop warring message.
- If user set non-security in config mode, the DUT will
pop warring message to inform user.
- support multi-language in ap mode or router mode.
- support power saving mode (802.3 az)

2. Fixed Bug :
-BugNo:5967: when re-access status on new window, another window will show wrong information.
-BugNo:5987: WLAN with schdules is failed for AP mode. Clients can not survey or connect with
    DUT when time is on schedule. (Not support schedule for AP Mode)
-BugNo:6002: WPS function keep count-down and show connection failed while running WPS and client connect successful.
-BugNo:6006: Can not set WEP security.
-BugNo:6977: AP mode Timeout, APUT UI should not go to login page when UI idle 3 minutes on status/device info page.
-BugNo:6981: wrong warning message when security set WEP or WPA-PSK.
-BugNo:5961: DUT would reconnect automatically when WAN is PPPoE on demand.
-BugNo:6005: If SSID contain of ", SSID would show incorrectly on wireless setting page.
-BugNo:5995: Netbios name would fail when user client is WIN XP or no support IPv6. Please follow D-Link AP
    and Router Device Management v1.01
-BugNo:6175:  Multicast Stream (IGMP Snooping) - IPv4 and IPv6.
-BugNo:6181:  wrong model name on step 4 in setup wizard.
-BugNo:6486:  AP: DUT should generate auto IP (169.254.*.*).
-BugNo:6983:  HNAP Extension for IPv6 v1.00 v1.01R.
-BugNo:6975:  D-Link AP and Router Device Management v1.01; can't access APUT by http://dlinkapWXYZ
     (WXYZ: 4 digits suffix of MAC Address)
-BugNo:5998: If SSID contain of special character then next step GUI would show incorrectly on wlan wizard.
-BugNo:5929: Didn't support 404 error page. ver1.00NAB05 -->fail. a. wrong DUT icon on 404 page.
-BugNo:5984: error on status page.
-BugNo:6949: Wrong device icon on 404 error page.
-BugNo:6988: D-Link Consumer AP Web UI Specification v1.05
-BugNo:6974: DUT need reboot by manual after FW downgrade.
-BugNo:6181: wrong model name on step 4 in setup wizard.
-BugNo:5992: AP: Please follow D-Link Consumer AP Setup Wizard Specification v1.04
-BugNo:6984: AP:Storage devices list would be re-order after reboot. User would not access file.
-BugNo:6986: AP:File size can't over 10mb to upload. UI would show "413 – Request Entity Too Large" and no back to prev page
-BugNo:6554: IPv6 Spec. 1.4 E27, 29: N/C, there is no release function for test.
1.4 G36: WEBGUI system check IPv6 ping function failed.
1.5 D24, 26: N/C, there is no release function for test.
1.8: N/C, not support
2.7: MTU set 1300, CE-Router doesn't transmit a valid ICMPv6 packet too big message to TAR-Host1
4.1, 4.2: CE-Router can't transmit RA when CE-Router to generate ULA prefix

======================================================================================
Firmware Version: ver1.00b17
Firmware Date: Tue, 9, Aug, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x173A64A0
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2413
APPS SVN Revision: 2409
APPS_CGI SVN Revision: 6282
WIRELESS SVN Revision: 37
PLATFORM SVN Revision: 187
ATHSDK SVN Revision: 76

1. Feature:
- All PLC function except PLC QoS

2. Fixed Bug:
PLC
- BugNo:6910 IE popup javascript error Excepted ';'
- BugNo:6912 Network name setting would be set to public after add a member.
- BugNo:6913 Please add "reboot now" button after click reboot later button.
- BugNo:6914 Mac address field would be input 'undefined' after add a member.

AP Mode
- BugNo:6976 Device name can't change setting on LAN settings page.
- BugNo:6979 copyright description should be white on rebooting page after set LAN IP setting.
- BugNo:6980 Please remove "auto update" button on language pack version check.
- BugNo:6982 please add ping result string for D-Link Access Point IPv6 Specification_v1.02.

======================================================================================
Firmware Version: ver1.00b16
Firmware Date: Wed, 3, Aug, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x870FF963
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2313
APPS SVN Revision: 2312
APPS_CGI SVN Revision: 6257
WIRELESS SVN Revision: 36
PLATFORM SVN Revision: 179
ATHSDK SVN Revision: 76

1. Feature:
- Support DHCPv6 Release and Renew Button in IPv6 status page. (Autoconfiguration Mode)
- DDNS Specification v1.06R-Draft
- HNAP Extension for IPv6 v1.00? v1.01R
- Router Web File Access Specification v1.02

2. Fix Bug:
- BugNo:6950 IPv6 Spec 1.19 -->Fail (ULA address would access internet on IPv6 PPPoE mode)
- BugNo:5909 Webgui shouldn't user to input username and password when website be block with access control rule.
- BugNo:5931 Please modify username login method and copyright.

AP Mode
- BugNo:6483 AP: Please follow D-Link Consumer AP Web UI Specification V1.04
 -->Fail (IPv6 description is wrong on LAN SETUP page.)
- BugNo:6485 DUT shouldn't naming "D-link Router_log.txt" while click Save Log button on logs page.
 -->Fail (it still naming D-link Router_log.txt)
- BugNo:6948 AP:There is no "reboot now" button on LAN setup, PLC setting, Network filter, ADV wireless,
 user limit, admin, time, pages after click reboot later.
- BugNo:5999 AP: Need reboot DUT manually after apply functions who are reboot, upgrade FW, load setting, reset to default.
- BugNo:5989 AP: Wrong login behavior.
- BugNo:5994 AP: DUT can't query host name, because there is no DNS address filed for input.
 ver1.00NAB12 -->Fail (DUT doesn't query host name) -->Fail (still doesn't query host name on static mode)

Language Pack
- BugNo:6487 Can't upload language pack on AP mode.
- BugNo:6488 Can't check new language pack or firmware in internet.

======================================================================================
Firmware Version: ver1.00b15
Firmware Date: Mon, 25, Jul, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0xE16D465D
CONFIG_VERSION: 1.00
Language: DEFAULT
Language-Version: ver0.00b00
Language-Checksum: 0x00000000
WWW SVN Revision: 2190
APPS SVN Revision: 2188
APPS_CGI SVN Revision: 6196
WIRELESS SVN Revision: 32
PLATFORM SVN Revision: 171
ATHSDK SVN Revision: 70

1. Feature:
- IPv6 Spec 1.19
- Web File Access delete acoount support.

2. Fix Bug:
Router Mode
- BugNo:6480 Chklst content isn't follow SPEC v1.15.
 (A. MAC address and channel list format. B. add Language information. C. default item shouldn't always be 0.)
- BugNo:6481 Please modify release note information about language.
- BugNo:6917 Please add language info and modify FW notify on chklst.txt
- BugNo:6918 Please modify FW version and FW query on version.txt
- BugNo:6555 Doesn't support device management when use IPv6 address. Link local address is OK.

AP Mode:
- BugNo:6482 AP: system check function is fail. Can't show after click ping.
- BugNo:6483 AP: Please follow D-Link Consumer AP Web UI Specification V1.04
 (index, LAN, IPv6 list, advanced wireless, status, stauts/wireless, tools/admin, tools/firmware, tools/time,
  tools/schedule, wireless/WEP&PSK&EAP, support/LAN&status&wireless&tools )
- BugNo:6484 Please modify helpful hints about visibility status on wireless page.
- BugNo:6485 DUT shouldn't naming "D-link Router_log.txt" while click Save Log button on logs page.
- BugNo:6012 AP: Please remove string about DHP-306AV or DUT function item on helpful hints.(fig19~21)
 Ex. user limit, lan setting and admin page. ver1.00NAB12-->Fail (user limit, lan setting and admin page don't modify)
- BugNo:5994 AP: DUT can't query host name, because there is no DNS address filed for input. ver1.00NAB12
 -->Fail (DUT doesn't query host name)

======================================================================================
Firmware Version: ver1.00NAb14
Firmware Date: Fri, 15, Jul, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x2BF46B50
CONFIG_VERSION: 1.00
WWW SVN Revision: 2087
APPS SVN Revision: 2087
APPS_CGI SVN Revision: 6169
WIRELESS SVN Revision: 29
PLATFORM SVN Revision: 156
ATHSDK SVN Revision: 68

1. Feature:
- PLC SETTINGS(Network Name, Add Member, Member List)

======================================================================================
Firmware Version: ver1.00NAb13
Firmware Date: Fri, 3, Jun, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: Date: Thu, 15, Mar, 2011
checksum: 0x5FC1DF9E
CONFIG_VERSION: 1.00
WWW SVN Revision: 1629
APPS SVN Revision: 1629
APPS_CGI SVN Revision: 5851
WIRELESS SVN Revision: 11
PLATFORM SVN Revision: 74
ATHSDK SVN Revision: 39

1. Feature:
- IPv6 Spec 1.18 without SNTP option for DHCPv6
- Follow TR-124 issue 2 Autoconfiguration flow in Autoconfigure Mode, PPPoE Mode, Autodetect Mode, IPv6 Wizard.
- Add connect/distconnect button in IPv6 status page when IPv6 PPPoE is share with IPv4 PPPoE.

======================================================================================
Firmware Version: ver1.00NAb12
Firmware Date: Fri, 27, May, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
checksum: 0xA8B49F63
CONFIG_VERSION: 1.00
WWW SVN Revision: 1540
APPS SVN Revision: 1540
APPS_CGI SVN Revision: 5813
WIRELESS SVN Revision: 10
PLATFORM SVN Revision: 65
ATHSDK SVN Revision: 28


1. Fix Bug :
Router Mode
- BugNo:5925 Can't access XML agent. Can't login or get info via widget and gadget.
- BugNo:5960 Please add 24 hours format.
- BogNo:6307 GUI would pop-up wrong message when set a schedule rule and click reboot later then go to other page.


AP Mode:
- BugNo:5988 If SSID contain of special character then next step GUI would show incorrectly on wlan wizard.(fig1)
- BugNo:5991 Follow D-Link Consumer AP Web UI Specification V1.04.(fig3~8).
- BugNo:5994 DUT can't query host name, because there is no DNS address filed for input.
- BugNo:5995 support Netbios name (IPv4) when user client is WIN XP.
- BugNo:6002 WPS function keep countdown and show connection failed while running WPS and client connect successful.
- BugNo:6003 PIN code would disappear, when disable WPS then enable.
- BugNo:6004 GMP snooping function is always enabled.
- BugNo:6005 If SSID contain of ", SSID would show incorrectly on wireless setting page.(fig13).
- BugNo:6006 Can't set WEP security.
- BugNo:6007 Can't set wireless channel.(fig14).
- BugNo:6012 Please remove string about DHP-306AV or DUT function item on helpful hints.(fig19~21) Ex. user limit, lan setting and admin page.
- BugNo:6013 DUT MAC address on recovery mode is different on normal.
- BugNo:6187  can't access chklst.txt and version.txt

2. Test:
- BT

3. Feature:
- Language Pack
======================================================================================
Firmware Version: ver1.00NAb11
Firmware Date:Wed, 25, May, 2011Fri, 27, May, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
checksum: 0x6B82B28C
CONFIG_VERSION: 1.00
WWW SVN Revision: 1520
APPS SVN Revision: 1520
APPS_CGI SVN Revision: 5793
WIRELESS SVN Revision: 10
PLATFORM SVN Revision: 62
ATHSDK SVN Revision: 25


1. Test
- HWNAT Throughput
======================================================================================
Firmware Version: ver1.00NAb10
Firmware Date:Mon, 16, May, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
checksum: 0xF9AE8049
CONFIG_VERSION: 1.00
WWW SVN Revision: 1452
APPS SVN Revision: 1452
APPS_CGI SVN Revision: 5686
WIRELESS SVN Revision: 9
PLATFORM SVN Revision: 61
ATHSDK SVN Revision: 23

1. Fix Bug
- BugNo:5929 Don't support 404 error page.
- BugNo:6181 wrong model name on step 4 in setup wizard.
- BugNo:6276 should power on and off manual after switch AP to RT or RT to AP.
- BugNo:6304 DNS address should be input correct IP and gray out when advanced DNS enabled on setup wizard setting.
- BugNo:6305 DNS address should be input correct IP and gray out when advanced DNS enabled on internet wizard setting.
- BugNo:6306 WLAN security would be set incorrectly after select automatically assign key via setup wizard. (always be set 1234567890).
- BugNo:6308 Graph authentication function would work without reboot. Set graph authentication enabled or disabled and
    click reboot later then close browser and re-login.

2. Test
- Router Mode BT

======================================================================================
Firmware Version: ver1.00NAb09
Firmware Date:Fri, 29, Apr, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
checksum: 0x2823CEEA
CONFIG_VERSION: 1.00
WWW SVN Revision: 1362
APPS SVN Revision: 1362
APPS_CGI SVN Revision: 5618
WIRELESS SVN Revision: 4
PLATFORM SVN Revision: 49
ATHSDK SVN Revision: 19

1. Fix Bug
Router Mode:
- BugNo:6178 Clone MAC address function display is OK, but sniffer WAN MAC is original after configured from setup wizard.
- BugNo:6189 RT, status page hasn't guest zone security.
- BugNo:6272 Can't login DUT after enabled graph authentication and selected "reboot later" via setup wizard.
- BugNo:6273 Can't detect pppoe session on setup wizard detect internet.
- BugNo:6274 prev button is fail on access control.

======================================================================================
Firmware Version: ver1.00NAb08
Firmware Date:Mon, 25, Apr, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
checksum: 0x3CCAB6E9
CONFIG_VERSION: 1.00
WWW SVN Revision: 1311
APPS SVN Revision: 1311
APPS_CGI SVN Revision: 5587
WIRELESS SVN Revision: 4
PLATFORM SVN Revision: 48
ATHSDK SVN Revision: 19

1. fix bug
AP Mode:
- BugNO:6185 AP Mode: Please modify login information and title description
- BugNo:6186 AP Mode: Can't login DUT on AP mode after reset to default
- BugNo:6187 RT Mode: Web GUI can't access after used system check function

RT Mode:
- BugNo:5910 Machines in the rule would be blocked when Access control method is Log web access only.
- BugNo:5959 Please add guest zone info in status.

Setup Wizard 1.01
-BugNo:6177 can't display "Unable detection (5.2.1)" in setup wizard.
-BugNo:6179 graph authentication always disabled after configured from setup wizard.
-BugNo:6180 next button on step 3 sometime wouldn't work (no response) in setup wizard.
-BugNo:6182 gui error on setup wizard after set illegal key.
-BugNo:6183 IP/mask/gateway would show NULL on finish information (wan set dhcp) setting in setup wizard.
-BugNo:6184 there is no enough information after completed setup wizard.
MUltiple:
Bug:6024
- Multiple Settings: This is linux base behavious, not a bug
- Multiple Settings: access control item couldn't be set and saved if ever apply the "reboot later"

======================================================================================
Firmware Version: ver1.00NAb07
Firmware Date:Fri, 15, Apr, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
CheckSum: 0x81061A8D
WWW SVN Revision: 1258
APPS SVN Revision: 1258
APPS_CGI SVN Revision: 5543
WIRELESS SVN Revision: 4
PLATFORM SVN Revision: 44
ATHSDK SVN Revision: 19

1. fix bug
-. BugNo:5895 DUT should reboot automatically after applying upgrade FW, reset to default, upload configured file or reboot.
-. BugNo:5910 Machines in the rule would be blocked when Access control method is Log web access only.
-. BugNo:6099 GUI would be crash after rebooting or resetting and access web GUI Immediately.
-. BugNo:6176 Widget WAN port speed wouldn't display.
-. BugNo:5925 Can't access XML agent. Can't login or get info via widget and gadget.

2. function test
Support multiple settings before reboot the device.

======================================================================================
Firmware Version: ver1.00NAb06
Firmware Date:Fir, 1, Apr, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
CheckSum: 0xF2EDFF95
WWW SVN Revision: 1170
APPS SVN Revision: 1170
APPS_CGI SVN Revision: 5498
WIRELESS SVN Revision: 3
PLATFORM SVN Revision: 32
ATHSDK SVN Revision: 9

1. fix bug
-. BugNo:6101 - There is a wrong information in version.txt (Firmware Notify => Firmware Query)
-. BugNo:6102 - The DUT should be hidden guest zone information when guest zone is disabled.
-. BugNo:6098 - PPTP MPPE encryption is fail. Can't set 40 bit or 128 bit.
-. BugNo:6100 - Wrong information in chklst.txt.
-. BugNo:5986 AP - GUI would pop-up error after set schedule rule.
-. BugNo:5990 AP - Can't display picture at above and blow.
-. BugNo:5993 AP - GUI would pop-up error and no information to notify after set DUT IP.
-. BugNo:5996 AP - Copyright is different form login page.
-. BugNo:5997 AP - Error on status page.
-. BugNo:5998 AP - Error on tools/system page.
-. BugNo:6000 AP - GUI would pop-up error after click check button on firmware page.
-. BugNo:6001 AP - There is no current FW date on firmware page.
-. BugNo:6008 AP - Day and hour is empty on time manual page.
-. BugNo:6009 AP - Please remove email log button.
-. BugNo:6010 AP - There are no information on IPv6 status and it would pop-up object error message.(fig17,18)
-. BugNo:6011 AP - GUI would pop-up error after set ipv6 setting on lan page.



2. function test
IPv6 - Spec. 1.17R
-. Support four DNSs, and send the query to IPv6 DNS first.
-. Update DHCPv6 AFTR_NAME option code from 99 to 64.
-. Copy "Local Doamin Name" which is in NETWORK SETTING to Domain Search List in RA and DHCP6S.
-. If the PD is changed. Advertising the old prefix with a preferred lifetime of zero and a valid lifetime of two hours in RA.

Multicast Stream (IGMP Snooping)
- IPv4 and IPv6

Widget

Setup Wizard 1.01

3.
BT

======================================================================================
Firmware Version: ver1.00NAb05
Firmware Date:Fir, 25, Mar, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Thu, 15, Mar, 2011
CheckSum: 0x15FBA5C4
WWW SVN Revision: 1106
APPS SVN Revision: 1106
APPS_CGI SVN Revision: 5447
WIRELESS SVN Revision: 2
PLATFORM SVN Revision: 24
ATHSDK SVN Revision: 7

1. fix bug
1. BugNo:5914 PPTP authentication protocol is failed. Ex DUT set PAP and VPN server set MSCHAPv2 only, DUT still connects.
2. BugNo:5962 Routing between zone function is always enabled in guest zone
3. BugNo:5929 Didn't support 404 error page.
4. Access UI page response with slow (os:XP)


2. function test
1. ADVANCED WIRELESS
- WLAN Partition

2. IPv6
- Support DHCP-PD hint always request the previous prefix.
    - Disable UI of DHCP-PD hint.
    - 6to4.
    - 6rd.


======================================================================================
Firmware Version: ver1.00NAb04
Firmware Date:Fir, 18, Mar, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Fir, 11, Mar, 2011
CheckSum: 0xA9A74476
Rootfs SVN Revision: 1050
WWW SVN Revision: 1050
APPS SVN Revision: 1049
WIRELESS SVN Revision: 2
PLATFORM SVN Revision: 2
ATHSDK SVN Revision: 2

1. fix bug
1. BugNo:5914 PPTP authentication protocol is failed. Ex DUT set PAP and VPN server set MSCHAPv2 only, DUT still connects.
2. BugNo:5922 Disabled Always broadcast isn't functional on network setting.
3. BUgNo:5926 DUT MAC address on recovery mode is different on normal.
4. BugNo:5929 Didn't support 404 error page.
5. BugNo:5930 There are wrong information and wrong layout on internet session page. (see fig18)
6. BugNo:5958 Revoke link isn't functional in DHCP client list
7. BugNo:5959 Please add guest zone info in status
8. BugNo:5961 DUT would reconnect automatically when WAN is PPPoE on demand
9. BugNo:5962 Routing between zone function is always enabled in guest zone
10. BugNo:5963 Clients connected with guest zone shouldn't access DUT
11. BugNo:5982 wrong FW version in version.txt file
12. BugNo:5983 wrong WLAN MAC in chklst.txt file
13. BugNo:5984 error on status page
14. BugNo:6019 DUT SSID is wrong after DUT running WPS with PBC. SSID should be: dlinkxxxx (xxxx is the last four digit of the LAN MAC address of the router)
15 FW file naming wrong


2. function test
1. FIREWALL SETTINGS
- NAT Endpoint Filter
- Anti-Spoof Checking
- DMZ
- ALG-IPSec
- ALG-RTSP
- ALG-SIP
2. ADVANCED WIRELESS
- Beacon Period
- RTS Threshould
- Fragmentation Threshould
- DTIM Interval
- WLAN Partition
- WMM Enable
- Short GI

2. SYSLOG
3. LOGS

======================================================================================
Firmware Version: ver1.00NAb03
Firmware Date:Fir, 11, Mar, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 003, Date: Fir, 11, Mar, 2011
CheckSum: 0x02E04F45
Rootfs SVN Revision: 968
APPS SVN Revision: 5321
Eagles APP: 2034

1. fix bug
1. BugNo:5896 Firmware check and language check aren't functional. WAN side can't capture to query packet.
2. BugNo:5898 Chklst contents are wrong. (see fig1, fig2, fig3) http://172.21.49.165/bbs/rcbbs/ShowPost.asp?id=286
3. BugNo:5899 Firmware version display and query firmware website address are wrong. Shouldn't have "NA" (see fig4, fig3)
4. BugNo:5900 WAN status usually display wrong. Wrong MAC address; wrong DNS when WAN set static DNS; wrong IP,
subnet mask and gateway; wrong connection type when WAN set static IP; wrong uptime. (see fig5~fig10)
5. BugNo:5905 Error on support_internet page. (see fig12)
6. BugNo:5910 Machines in the rule would be blocked when Access control method is Log web access only.
7. BugNo:5912 Action selection is wrong on inbound filter page.
8. BugNo:5914 PPTP authentication protocol is failed. Ex DUT set PAP and VPN server set MSCHAPv2 only, DUT still connects.
9. BugNo:5918 Please modify description on firmware page. (see fig15)
10. BugNo:5919 Secondary WINS IP address should be optional on DHCP server settings.
11. BugNo:5923 IPv6 status is wrong. Sometime would display previous setting. (see fig16)
12. BugNo:5926 DUT MAC address on recovery mode is different on normal.
13. BugNo:5930 There are wrong information and wrong layout on internet session page. (see fig18)
14. BugNo:5931 Please modify username login method and copyright. (see fig19)
15. BugNo:5932 When double or treble click "Don't save settings" button, GUI just pop-up abandon message.(see fig20)
16. BugNo:5933 Sometime DHP-1565 graph would be loaded. (see fig21)
17. BugNo:5954 Please remove set wlan radio mode on wlan wizard
18. BugNo:5955 WLAN will be disabled after running WLAN wizard and select auto assign network key. And user can select WLAN radio mode
19. BugNo:5957 Lock wireless security settings isn't functional in WPS
20. BugNo:5958 Revoke link isn't functional in DHCP client list
21. BugNo:5959 Please add guest zone info in status
22. BugNo:5964 DS-lite doesn't in WAN list
23. BugNo:5965 Error on the DDNS page after DDNS setting
24. BugNo:5966 gateway address should be show 0.0.0.0 when network status is disconnected

2. Function test
1. FIREWALL SETTINGS
- SPI
2.ADVANCED NETWORK
- WAN Port Speed
3. AP mode (all function )
4.IPv6
- If DHCP-PD is enabled, the Lifetime field in IPv6 LAN Address Autoconfiguration Settings should be grayed out,
and the prefer time and valid time should follows exactly the same value received in DHCP-PD.
- Router LifeTime should inherits the RA lifetime form the upstream router.
- Support DNSSL (RFC6106)
- Support a input-box for manual IA_PD hint configuration.
5.ACCESS CONTROL
- Web Access Logging
======================================================================================

Firmware Version: ver1.00NAb02
Firmware Date:Fir, 24, Feb, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 002, Date: Thu, 24, Feb, 2011
CheckSum: 0xC8F1B2F6
Rootfs SVN Revision: 897
APPS SVN Revision: 5246
Eagles APP: 2018

Problems Resolved:
1. fix bug
1. NO:4 DNS address field in internet setup wizard shouldn't be change when advanced DNS enabled.
2. NO:6 Firmware check and language check aren't functional. WAN side can't capture to query packet.
3. NO:7 Firmware naming is wrong. http://172.21.49.165/bbs/rcbbs/ShowPost.asp?id=280
4. NO:8 Chklst contents are wrong. (see fig1, fig2, fig3) http://172.21.49.165/bbs/rcbbs/ShowPost.asp?id=286
5. NO:9 Firmware version display and query firmware website address are wrong. Shouldn't have "NA" (see fig4, fig3)
6. NO:10 WAN status usually display wrong. Wrong MAC address; wrong DNS when WAN set static DNS; wrong IP, subnet mask and gateway; wrong connection type when WAN set static IP; wrong uptime. (see fig5~fig10)
7. NO:11 WAN release/renew button or connect/disconnect button are failed. There aren¡¦t functional.
8. NO:12 Error on status page. (see fig11)
9. NO:13 MAC clone button isn't functional in internet setup wizard, WAN setting and access control item.
10. NO:14 DHCP routing option item can't save setting and work. Please add function description in support.
11. NO:15 Error on support_internet page. (see fig12)
12. NO:16 Graphical authentication graph should update automatically when authentication failed.
13. NO:18 Wrong word is idle not idel. Idle time should invalid to key-in not a number.
14. NO:21 Can't save the 22nd, 23rd and 24th port forwarding rules.
15. NO:23 Idle time works failed. Webgui always logout on setting time while user using.
16. NO:25 DUT didn't detecting and detect status bar didn't work on IPv6IPv6 internet connection setup wizard.
17. NO:26 DUT still use DHCPv6 IP to access when use Link-local address on Static IPv6.
18. NO:27 Please add DHCP-PD in LAN item on 6rd.(please check this function)
19. NO:28 Please modify description on firmware page. (see fig15)
20. NO:29 Secondary WINS IP address should be optional on DHCP server settings.
21. NO:30 DHCP client list usually empty after DUT save other setting.
22. NO:31 Disabled DNS relay isn't functional on network setting.
23. NO:32 Disabled Always broadcast isn't functional on network setting.
24. NO:33 IPv6 status is wrong. Sometime would display previous setting. (see fig16)
25. NO:34 Error on 6rd page after set setting.
26. NO:37 Can't upload FW and show "upgrade failed" using Chrome or Safari on recovery mode. Webgui would hang up using Firefox on recovery mode.
27. NO:40 There are wrong information and wrong layout on internet session page. (see fig18)
28. NO:41 Please modify username login method and copyright. (see fig19)
29. NO:42 When double or treble click "Don't save settings" button, GUI just pop-up abandon message.(see fig20)

2.Function test
1.BASIC TEST
- Wireless Connectivity

2.PLATFORM
- LIGHTTPD IPv6

3.Setup
1.INTERNET
- DS-Lite
2.WIRELESS(including IOT)
- not support
1. Wizard WPS Push Button
2. IGMP snooping
3.IPv6
Manual -> Auto Detection

4.ADVANCED
1. VIRTUAL SERVER
- Schedule
2. PORT FORWARDING
- Schedule
3. APPLICATION RULE
- Schedule
4.ACCESS CONTROL
- Schedule
5.FIREWALL SETTINGS
- NAT Endpoint Filter
- Anti-Spoof Checking
- DMZ
- ALG-RTSP
- ALG-SIP
6.ADVANCED WIRELESS
- Beacon Period
- RTS Threshould
- Fragmentation Threshould
- DTIM Interval
- WLAN Partition
- WMM Enable
- Short GI
7.WI-FI PROTECTED SETUP
8. GUEST ZONE
9. IPv6 FIREWALL RULES
10. IPv6 ROUTING

5.TOOOLS
1. SCHEDULE

6.STATUS
1.LOGS
2.WIRELESS
3.IPv6

7.HNAP

======================================================================================


Firmware Version: ver1.00NAb01
Firmware Date:Wed, 26, Jan, 2011
KERNEL: 2.6.31
SDK: 1.0, Build: 001, Date: Wed, 26, Jan, 2011
CheckSum: 0x1733364D
Rootfs SVN Revision: 836
APPS SVN Revision: 5101
Eagles APP: 1983

Problems Resolved:
1.First release

2.chklst.txt

3.Backup Mode

4.SETUP
- INTERNET
o. Wizard(DHCP, Static, PPPoE, L2TP)
o. DHCP
o. PPPoE
o. PPTP
o. L2TP
o. Static
o. DS-Lite
- IPv6
o. WIZARD
o. Static IPv6
o. Auto-Detection
o. Autoconfiguration(SLAAC/DHCPV6)
o. PPPoE
o. IPv6 in IPv4 Tunnel
o. 6to4
o. 6rd
o. Link-Local only
- PLC LAN

5.ADVANCED
- Virtual Server
o. Virtual Server function
o. Virtual Server with Schedule
- Port Forwarding
o. Port Forwarding
o. Port Forwarding with Schedule
o. Port Forwarding with Inbound Filter
- Network Filter function
- Access Control
- Website Filter
- Inbound Filter
- Firewall Setting
o. DMZ
o. ALG
- Advanced Network
o. UPNP
o. WAN Ping
o. WAN Ping with Inbound Filter
- IPv6 Firewall Rules
- IPv6 Routing

6.TOOLS
- Admin
- Time
- Email Settings
- Dynamic DNS
- System Check
- Schedules
- system

7.STATUS
- Device Info
- Statistics
- Internet Sessions
- Routing
- IPv6
- IPv6 Routing

======================================================================================

Stargate64

Salve a tutti!
Ho un problema con il router in oggetto.
Non importa quali settaggi io usi: il router non riesce a sincronizzare il suo orario con NESSUN server NTP, né quello della Dlink, né altro. Avrei bisogno di mantenere l'orario sul router per una serie di motivi, ma sembra che non ci sia nulla da fare.
Qualcuno ha una soluzione per questo problema?
Grazie anticipatamente!
Fabio

Carciofone

Che versione di firmware usi?
Che configurazione di connessione al modem è attiva nel DHP e nel modem di connessione?

Stargate64

Citazione di: C@rciofone il 15 Marzo 2014, 11:54:36Che versione di firmware usi?
Che configurazione di connessione al modem è attiva nel DHP e nel modem di connessione?
Ordunque... il firmware è il numero 1.03 del 1 Aprile 2013. Il modem è connesso, alla porta WAN, in modalità 1483 Bridged; il router "comanda" la connessione (non on-demand, ma costantemente) via PPPoE.
E grazie per l'interessamento!
Fammi sapere... ???

Carciofone

Allora, con quel firmware e provider Alice non riscontro problemi, l'orario si aggiorna automaticamenteall'accensione o riconnessione. Però ricordo che in studio, con provider kpnqwest ciò non accadeva perchè venivano bloccate le porte dei server ntp direttamente dal provider.

Stargate64

Citazione di: C@rciofone il 16 Marzo 2014, 07:25:51Allora, con quel firmware e provider Alice non riscontro problemi, l'orario si aggiorna automaticamenteall'accensione o riconnessione. Però ricordo che in studio, con provider kpnqwest ciò non accadeva perchè venivano bloccate le porte dei server ntp direttamente dal provider.

Io ho Alice, ma il problema c'è
Che mi suggerisci di fare?
Grazie ancora!

devilstorm

Sorry I do not speak italian that well, so I write in english :D

There is a modded firmware version that has removed issues with PLC of this device.

Apparently the firmware of the PLC has been updated to the lastes version.

Unfortunately I have to remove the download link because it requires the installation of a download manager to the users.

Carciofone

Hello devilstorm!
Could you indicate the source of this modded firmware?
There is a site or a blog reference?
There is also an official D-Link firmware 1.03B01.
Thanks

Licenza Creative Commons
Il contenuto dei messaggi del forum è distribuito con
Licenza Creative Commons Attribuzione Non commerciale 4.0
Tutti i marchi registrati citati appartengono ai legittimi proprietari